Adhesives & High Strength Glues Selangor, Malaysia, Kuala Lumpur (KL), Shah Alam, Singapore, China, Vietnam

PUTTY JOINTING ADHESIVE epigen 1614 p

Manufactured to a putty like viscosity, this flexible epoxy grouting & caulking system is designed for use as a concrete joint sealant in trafficable or heavy duty applications. Characterised by exceptional toughness and durability, use has extended to flexible grouting of equipment.
 
Epigen 1614P possesses exceptional water resistance and resistance to a broad range of chemicals including degreasers, cleaners, aviation fuels and lubricants, and a range of acid and alkali reagents.
 
TYPICAL APPLICATIONS
  • Vehicle Workshop Jointing        
  • Swimming Pool Joints
  • Carparks Jointing  
  • PVC Pipe Sealing
  • Sheet Plastic Adhesive             
  • Gasketing
  • Concrete Crack Repair              
  • Core Sampling
  • Rock Wall Consolidation  
  • Resilient Adhesive
  • Water Stop

FEATURES
  • Excellent chemical resistance
  • Food industry suitable
  • Internally plasticized - long term stability
  • Putty viscosity for inclined surface installation
  • Free of all solvents - zero VOC
  • Tough and durable
  • Versatility in application allows concrete patching
  • Suitable with large aggregate addition enables void filling while still retaining flexability
  • Strongly adhesive for optimum adhesion

Epigen 1614P is supplied as a two part kit comprising component “A” resin, and component “B” curative.
The entire kit is supplied in a pre weighed convenient size to make on site activities easier.
 
Peerless Industrial Systems can provide information on specific applications based on industry acceptable practices or historical results.

 
PROFILE    
Colour Grey  
Ratio by weight 3 kg Component “A” 
  1 kg Component “B”
Pot Life minutes @ 24oC 30  
Mixed consistency @ 24oC Non sag paste 
Specific gravity when mixed 1.6  
Coverage  20mm X 10mm 1.6 kg / 5 lineal metres
TYPICAL CURED PROPERTIES
Compressive strength ASTM D695, Mpa n/a 
Tensile strength ASTM D638, Mpa 2
Flexural strength ASTM D790, Mpa n/a
Elongation  at fracture % 50
Elongation after max strain  released % 2
Nominal  joint movement % 18
Maximum exposure temperature,  C 120
Heat deflection temperature ASTM D648, 
o C
<60 
Cure time to light traffic, Hours 14
Cure time to open traffic, Hours 24
Ultimate cure time, Hours 96

SURFACE PREPARATION

Methods for surface preparation prior to use include using chemical means such as washing & etching, high pressure water blasting, or mechanical techniques such as abrasive blasting, grinding or scarifying.
Specialist advice is available from Peerless Industrial Systems to ensure the correct preparation procedure is employed for specific application.


APPLICATION

Mixing of product should be carried out using slow speed mixers and completed by adding to the component “A”, component “B”. Ensure the mix is homogenus and free from lumps.

Jointing:

In all cases, the maximum joint depth should be 50% of joint width. The base of the joint must be unrestrained and clear of any adhesion to the base or backing tape. In extreme conditions of joint movement, installation should be carried out to enable cure to take place at the maxi- mum joint width. No edge primer is required to facilite adhesion unless the surface is loose or friable. In cool environments, pre warm the product before use.

Adhesive Applications:

Apply a thin coat of Epigen 1614P to both surfaces before bring the two together. Do not use where a hard high strength glue line is required. Recommended where a resilient or shock resistant bond is required (eg: PVC to concrete, HDPE onto steel, Rubber onto steel). Preheat the material before use to acheive best cure rate and strength

Crack Repairs: Non structural

In horizontal or vertical applications, open up cracks or chase using grinder before placing directly into crack using spatula or gun. Area of application may require top dressing as settling occurs.

COVERAGE GUIDE      
Jointing Application - nominally 20mm wide  
“Final Depth” < “Joint Width”  
1.6kg = 20mm X 10mm X 5 lineal metres  
Backing material must release cleanly from product 
Adhesive or Void Filling Application  
1.6kg = 1 litre      
1.6kg = 100mm X 100mm X 100mm  

CHEMICAL RESISTANCE
Tested at 21oC. Samples cured for 10 days at 25oC. Curing at elevated temperatures will improve chemical resistance.
 
1 = Continuous or long term immersion
2 = Short term immersion
3 = Splash and spills
4 = Avoid contact


Acetic Acid, 10 % 2 Acetone 2
Acetic Acid, Glacial 2 Ammonium Chloride 1
Hydrochloric Acid, 5 % 1 Beer 1
Hydrochloric Acid, 10 % 2 Dichloromethane 4
Hydrochloric Acid, conc 2 Diesel Fuel 1
Nitric Acid, 5 % 2 Isopropyl Alcohol 2
Nitric Acid, 10 % 2 Kerosene 1
Phosphoric Acid, 5 % 1 Petrol 2
Phosphoric Acid, 20 % 2 Salt Water 1
Sulfuric Acid, 5 % 3 Sewage 2
Sulfuric Acid, 20 % 3 Skydrol 2
Ammonium Hydroxide, 5 % 1 Sodium Cyanide 1
Ammonium Hydroxide, 20 % 1 Sodium Hypochlorite 2
Potassium Hydroxide,
5 %
1 Toluene 2
Potassium Hydroxide,
20 %
1 Trichloroethane 3
Sodium Hydroxide, 5 % 1 Wine 2
Sodium Hydroxide, 20 % 1 Xylene 2


CURE

Variations in cure may arise due to the amount of material being applied, the thickness of material being applied, the surface temperature, and the product temperature. The cure may be increased by heating product or by leaving mixed material stand for 15 minutes before use. The cure may be decreased by cooling the product before mixing.

LV JOINTING ADHESIVE epigen 1614

A low viscosity, flexible epoxy grouting & caulking system designed for use as a concrete joint sealant in trafficable or heavy duty applications. Characterised by exceptional toughness and durability, use has extended to flexible grouting of equipment and concrete crack injection.
 
Epigen 1614 possesses exceptional water resistance and resistance to a broad range of chemicals including degreasers, cleaners, aviation fuels and lubricants, and a range of acid and alkali reagents.
 
TYPICAL APPLICATIONS

  • Vehicle Workshop Jointing        
  • PVC Pipe Sealing
  • Swimming Pool Joints
  • Carparks Jointing  
  • Sheet Plastic Adhesive             
  • Gasketing
  • Concrete Crack Repair              
  • Core Sampling Rock
  • Wall Consolidation  
  • Resilient Adhesive
  • Water Stop

FEATURES
  • Excellent chemical resistance
  • Food industry suitable
  • Internally plasticized - long term stability
  • Low viscosity for easy installation
  • Free of all solvents - zero VOC
  • Tough and durable
  • Versatility in application allows concrete patching
  • Suitable with aggregate addition enables void filling while still retaining flexability
  • Strongly adhesive for optimum adhesion

Epigen 1614 is supplied as a two part kit comprising component “A” resin, and component “B” curative. The entire kit is supplied in a pre weighed convenient size to make on site activities easier.
 
Peerless Industrial Systems can provide information on specific applications based on industry acceptable practices or historical results.


PROFILE      
Colour Grey    
Ratio by weight 3 kg Component “A”   
  1 kg Component “B”  
Pot Life minutes @ 24oC 30    
Mixed consistency @ 24oC Flowable Liquid   
Specific gravity when mixed 1.6    
Coverage  20mm X 10mm 1.6 kg / 5 lineal metres

TYPICAL CURED PROPERTIES

Compressive strength ASTM D695, Mpa                    n/a 
Tensile strength ASTM D638, Mpa                               2
Flexural strength ASTM D790, Mpa                            n/a
Elongation  at fracture %                                             50
Elongation after max strain  released %                       2
Nominal  joint movement %                                         18
Maximum exposure temperature,  C                         120
Heat deflection temperature ASTM D648,  C           <60 
Cure time to light traffic, Hours                                     14
Cure time to open traffic, Hours                                    24
Ultimate cure time, Hours                                              96

This information is supplied as an indicative reference only.
Caution should be used where direct comparisons with other products are to be made.


SURFACE PREPARATION

Methods for surface preparation prior to use include using chemical means such as washing & etching, high pressure water blasting, or mechanical techniques such as abrasive blasting, grinding or scarifying.
Specialist advice is available from Peerless Industrial Systems to ensure the correct preparation procedure is employed for specific application.

APPLICATION

Mixing of product should be carried out using slow speed mixers and completed by adding to the component “A”, component “B”. Ensure the mix is homogenus and free from lumps.

Jointing:

In all cases, the maximum joint depth should be 50% of joint width. The base of the joint must be unrestrained and clear of any adhesion to the base or backing tape. In extreme conditions of joint movement, installation should be carried out to enable cure to take place at the maxi- mum joint width. No edge primer is required to facilite adhesion unless the surface is loose or friable. In cool environments, pre warm the product before use.

Adhesive Applications:

Apply a thin coat of Epigen 1614 to both surfaces before bring the two together. Do not use where a hard high strength glue line is required. Recommended where a resilient or shock resistant bond is required (eg: PVC to concrete, HDPE onto steel, Rubber onto steel). Preheat the material before use to acheive best cure rate and strength.

Crack Repairs: Non structural

In horizontal installations, open up cracks or chase using grinder before pouring directly into crack. Area of pour may require top up.
In vertical installations, pre drill holes along crack line and epoxy in grease nipple casings. Seal crack with epoxy and insert lowest nipple, inject product until flow occurs at higher casing, insert nipple there and inject product until flow occurs, and continue similar procedure until the entire crack height has been completed

COVERAGE GUIDE      
Jointing Application - nominally 20mm wide  
“Final Depth” < “Joint Width”  
1.6kg = 20mm X 10mm X 5 lineal metres  
Backing material must release cleanly from product 
Adhesive or Void Filling Application  
1.6kg = 1 litre      
1.6kg = 100mm X 100mm X 100mm  

CHEMICAL RESISTANCE
Tested at 21oC. Samples cured for 10 days at 25oC. Curing at elevated temperatures will improve chemical resistance.
 
1 = Continuous or long term immersion
2 = Short term immersion
3 = Splash and spills
4 = Avoid contact


Acetic Acid, 10 % 2 Acetone 2
Acetic Acid, Glacial 2 Ammonium Chloride 1
Hydrochloric Acid, 5 % 1 Beer 1
Hydrochloric Acid, 10 % 2 Dichloromethane 4
Hydrochloric Acid, conc 2 Diesel Fuel 1
Nitric Acid, 5 % 2 Isopropyl Alcohol 2
Nitric Acid, 10 % 2 Kerosene 1
Phosphoric Acid, 5 % 1 Petrol 2
Phosphoric Acid, 20 % 2 Salt Water 1
Sulfuric Acid, 5 % 3 Sewage 2
Sulfuric Acid, 20 % 3 Skydrol 2
Ammonium Hydroxide,
5 %
1 Sodium Cyanide 1
Ammonium Hydroxide,
20 %
1 Sodium Hypochlorite 2
Potassium Hydroxide, 5 % 1 Toluene 2
Potassium Hydroxide, 20 % 1 Trichloroethane 3
Sodium Hydroxide, 5 % 1 Wine 2
Sodium Hydroxide, 20 % 1 Xylene 2


 CURE

Variations in cure may arise due to the amount of material being applied, the thickness of material being applied, the surface temperature, and the product temperature. The cure may be increased by heating product or by leaving mixed material stand for 15 minutes before use. The cure may be decreased by cooling the product before mixing.

WET OR DRY UNDERWATER CURING PUTTY epigen 0503

Epigen 503 is a two component solventless epoxy which, when mixed, solidifies at ambient temperature to form a strong, tough material, possessing good mechanical properties and adhering strongly to suitably treated metal, timber and concrete surfaces.
 
It has been specifically designed to allow curing to take place unimpeded by the presence of water and Epigen 503 can therefore be used for underwater repairs and applications where dampness is present or the item being treated is subject to immersion prior to the Epigen 503 being cured.
 
Typical applications are the underwater patching of boat hulls, tanks, pipelines, and the repair or patching of tanks and concrete structures subject to immersion within a short time of application. Tidal zone repairs to steel and concrete wharf piles are also satisfactorily carried out using Epigen 503.


TYPICAL APPLICATIONS
  • Repairs to swimming pools including rebonding tiles
  • Fairing fibreglass and bonding fabrications
  • Pile Repairs
  • Corrosion resistant cladding on marine hulls
  • Grouting slipway rails
  • Concrete crack and void repair

FEATURES
  • Resistant to a variety of chemicals
  • Cures underwater - salt or fresh
  • Non sag putty viscosity for versatility
  • Free of all solvents - zero VOC
  • Tough and durable
  • Versatility in application allows concrete patching
  • Suitable on steel surfaces
  • Strongly adhesive for optimum adhesion

PROFILE    
Colour Off White  
Ratio by weight 1 kg Component “A”
  0.5 kg Component “B”
Pot Life minutes @ 24oC 30  
Mixed consistency @ 24oC Paste   
Specific gravity when mixed 1.4  


TYPICAL CURED PROPERTIES

Compressive strength ASTM D695, Mpa 82
Tensile strength ASTM D638, Mpa 22
Flexural strength ASTM D790, Mpa 32
Hardness, Shore D >85
Elongation ASTM D638, % 1.3
Tensile Adhesion ASTM 4541, MPa >12
Thermal conductivity ASTM C177, Kcal/m.hroC 0.6
Coeff of Therm Exp ASTM C531, 10-5/C 1.9
Maximum exposure temperature, C 115
Heat deflection temperature ASTM D648, C 75
Thin Film Gel @ 12mm, Minutes 60
Thin Film Set @ 12mm, Minutes 120
Ultimate cure time, Hours 96

SURFACE PREPARATION

Methods for surface preparation prior to use include high pressure water blasting, or mechanical techniques such as abrasive blasting, grinding or scarifying.m
Specialist advice is available from Peerless Industrial Systems to ensure the correct preparation procedure is employed for specific application.

APPLICATION

Mixing of product should be carried out using spatula or by slow speed blender, and completed by adding to the component “A”, component “B”. Ensure the mixed 0503 is homogenous and the final colour shall be even without streaks.When applying underwater, smear the 0503 across all surfaces to displace water.
 

Clading:

Depending on the situation, the depth should nominally be 2mm as minimum to ensure sufficent coverage is in place and afford reasonable mechanical strength. There is no maximum thickness reqirement. No primer is required to facilite adhesion unless the surface is loose or friable. In cool environments, pre warm the product before use.

Adhesive Applications:

Apply a thin coat of Epigen 0503 to both surfaces before bring the two together. Do not use where a flexible or resilient glue line is required. Recommended where a tough and strong, or heavy shock resistant material is required. Preheat the material before use to achieve best cure rate and strength when cold.

Crack & Cevice Repairs:

Open up cracks using a grinder to allow proper identifica- tion of imperfection before applying directly into crevice or crack.
   
CHEMICAL RESISTANCE
Tested at 21oC. Samples cured for 10 days at 25oC. Curing at elevated temperatures will improve chemical resistance.
1 = Continuous or long term immersion
2 = Short term immersion
3 = Splash and spills
4 = Avoid Contact 

                                                         
Acetic Acid, 10 % 2 Acetone 2
Acetic Acid, Glacial 2 Ammonium Chloride 1
Hydrochloric Acid, 5 % 1 Beer 1
Hydrochloric Acid, 10 % 2 Dichloromethane 4
Hydrochloric Acid, conc 2 Diesel Fuel 1
Nitric Acid, 5 % 2 Isopropyl Alcohol 2
Nitric Acid, 10 % 2 Kerosene 1
Phosphoric Acid, 5 % 1 Petrol 2
Phosphoric Acid, 20 % 2 Salt Water 1
Sulfuric Acid, 5 % 3 Sewage 2
Sulfuric Acid, 20 % 3 Skydrol 2
Ammonium Hydroxide,
5 %
1 Sodium Cyanide 1
Ammonium Hydroxide,
20 %
1 Sodium Hypochlorite 2
Potassium Hydroxide, 5 % 1 Toluene 2
Potassium Hydroxide,
20 %
1 Trichloroethane 3
Sodium Hydroxide, 5 % 1 Wine 2
Sodium Hydroxide, 20 % 1 Xylene 2


CURE

Variations in cure may arise due to the amount of material being applied, the thickness of material being applied, the surface temperature, and the product temperature. The cure may be increased by heating product or by leaving mixed material stand for 15 minutes before use. The cure may be decreased by cooling the product before mixing.

FASTPATCH ADHESIVE epigen FC3

A fast curing patching paste for repairing holes, cracks and gaps, characterized by the fibre reinforcement that allows voids to be bridged adding structural strength. Bonds to a variety of surfaces including steel, plastics, timber and fibreglass.
 
Extremely tough, it cures quickly to form a hard infusible plastic that resists impact and cracking.
 
Epigen FC3 possesses excellent water resistance and resists many harsh and aggresive chemicals including degreasers, cleaners, aviation fuels and lubricants, acid and alkali reagents.


TYPICAL APPLICATIONS

  • Pump and Cyclone Repairs
  • Pipe and Elbow patching
  • Sealing Oil Transformers
  • Patching holes in boats
  • Water pipe repair
  • Tank patching

FEATURES
  •  Fibre reinforced for strength 
  • Resistant to a variety of alkali & acids
  • Food industry suitable
  • Non sag viscosity for easy installation
  • Free of all solvents - zero VOC
  • Tough and durable
  • Suitable on steel to patch all breaks and gaps
  • Exhibits strong adhesive to plastics including PVC

Epigen FC3 is supplied as a two part kit comprising component “A” resin, and component “B” curative.
The entire kit is supplied in a pre weighed convenient size to make on site activities easier.
 
Peerless Industrial Systems can provide information on specific applications based on industry acceptable practices or historical results.


PROFILE        
Colour Green      
         
Ratio by weight 1 kg Component “A”    
  0.5 kg Component “B”
Pot Life minutes @ 24oC 15      
Mixed consistency @ 24oC Paste       
Specific gravity when mixed 1.4      
Coverage /m 2 @ 10mm 14.0 kg      
TYPICAL CURED PROPERTIES

Compressive strength ASTM D695, Mpa 82
Tensile strength ASTM D638, Mpa 24
Flexural strength ASTM D790, Mpa 36
Hardness, Shore D >85
Elongation ASTM D638, % 0.7
Tensile Adhesion ASTM 4541, MPa >14
Thermal conductivity ASTM C177, Kcal/m.hroC 0.6
Coeff of Therm Exp ASTM C531, 10-5/C 1.5
Maximum exposure temperature, C 120
Heat deflection temperature ASTM D648, C 80
Thin Film Gel @ 6mm, Minutes 15
Thin Film Set @ 6mm, Minutes 30
Ultimate cure time, Hours 18

SURFACE PREPARATION

Methods for surface preparation prior to use include using chemical means such as washing & etching, high pressure water blasting, or mechanical techniques such as abrasive blasting, grinding or scarifying.
Specialist advice is available from Peerless Industrial Systems to ensure the correct preparation procedure is employed for specific application.

APPLICATION

Mixing of product should be carried out using spatula, and completed by blending the component “A” with component “B”. Ensure the mix is homogenous and free from lumps. The final colour shall be even green without streaks.
Smear a thin coat of Epigen FC3 to all surfaces before overlaying the paste across the entre area to complete the treatment. Do not use where a flexible or resilient glue line is required. Recommended where a tough and strong, or heavy shock resistant material is required.
In large voids, two applications may be applied to bridge the gap or lay a stick or rod to aid support of the Epigen FC3. During cure, exotherm can build up to cause sag.

 
CHEMICAL RESISTANCE

Tested at 21oC. Samples cured for 10 days at 25oC. Curing at elevated temperatures will improve chemical resistance.
 
1 = Continuous or long term immersion
2 = Short term immersion
3 = Splash and spills
4 = Avoid contact
                 

Acetic Acid, 10 % 1 Acetone 2
Acetic Acid, Glacial 2 Ammonium Chloride 1
Hydrochloric Acid, 5 % 1 Beer 1
Hydrochloric Acid, 10 % 2 Dichloromethane 4
Hydrochloric Acid, conc 2 Diesel Fuel 1
Nitric Acid, 5 %  2 Isopropyl Alcohol 1
Nitric Acid, 10 % 2 Kerosene 1
Phosphoric Acid, 5 % 1 Petrol 1
Phosphoric Acid, 20 % 2 Salt Water 1
Sulfuric Acid, 5 % 3 Sewage 2
Sulfuric Acid, 20 % 3 Skydrol 2
Ammonium Hydroxide, 5 % 1 Sodium Cyanide 1
Ammonium Hydroxide, 20 % 1 Sodium Hypochlorite 2
Potassium Hydroxide, 5 % 1 Toluene 2
Potassium Hydroxide, 20 % 1 Trichloroethane 3
Sodium Hydroxide, 5 % 1 Wine 1
Sodium Hydroxide, 20 % 1 Xylene 2

CURE
Variations in cure may arise due to the amount of material being applied, the thickness of material being applied, the surface temperature, and the product temperature. The cure may be increased by heating product or by leavingmixed material stand for 15 minutes before use. The cure may be decreased by cooling the product before mixing.

HI BOND ADHESIVE epigen 0911

A high strength multipurpose paste suitable for grouting and caulking, designed for use on a variety of surfaces including steel, concrete, timber and fibreglass.
Characterised by exceptional toughness and durability, use has extended to ceramic wear tile bedding and grouting, fairing blowholes on concrete, and pitting on steel surfaces prior to coating.
 
Epigen 911 possesses exceptional water resistance and resistance to a broad range of chemicals including degreasers, cleaners, aviation fuels and lubricants, and a range of acid and alkali reagents.


TYPICAL APPLICATIONS
  • Ceramic Wear Tile Adhesive
  • Applying Fillets and Aris to Steel Surfaces
  • Fairing Pitting and Hollows on Steel Tanks
  • Pile Capping
  • Concrete Crack and Void Repair
  • Anti Corrosion Barrier Lining


FEATURES
 
  • Excellent chemical resistance
  • Food industry suitable
  • Non sag viscosity for easy installation
  • Free of all solvents - zero VOC
  • Tough and durable
  • Versatility in application allows concrete patching
  • Suitable on steel to void fill or fair surfaces
  • Strongly adhesive for optimum adhesion
Epigen 911 is supplied as a two part kit comprising component “A” resin, and component “B” curative.
The entire kit is supplied in a pre weighed convenient size to make on site activities easier.
 
Peerless Industrial Systems can provide information on specific applications based on industry acceptable practices or historical results.


PROFILE        
Colour Off White      
         
Ratio by weight 1 kg Component “A”    
  1 kg Component “B”
Pot Life minutes @ 24oC 30      
Mixed consistency @ 24oC Paste       
Specific gravity when mixed 1.4      
Coverage /m 2 @ 10mm 14 kg      
 
TYPICAL CURED PROPERTIES
Compressive strength ASTM D695, Mpa 70
Tensile strength ASTM D638, Mpa 18
Flexural strength ASTM D790, Mpa 32
Hardness, Shore D >85
Elongation ASTM D638, % 1.0
Tensile Adhesion ASTM 4541, MPa >12
Thermal conductivity ASTM C177, Kcal/m.hrC 0.6
Coeff of Therm Exp ASTM C531, 10-5/C 2.0
Maximum exposure temperature, C 120
Heat deflection temperature ASTM D648, C 75
Thin Film Gel @ 1mm, Minutes 180
Thin Film Set @ 1mm, Minutes 240
Ultimate cure time, Hours 96


SURFACE PREPARATION                                                          
Methods for surface preparation prior to use include using chemical means such as washing & etching, high pressure water blasting, or mechanical techniques such as abrasive blasting, grinding or scarifying.                          
Specialist advice is available from Peerless Industrial Systems to ensure the correct preparation procedure is employed for specific application.                                      
                                                                 
APPLICATION                                                            
Mixing of product should be carried out using spatula or by slow speed blender, and completed by adding to the component “A”, component “B”. Ensure the mix is homog- enous and even in colour.                            
                                                                 
Bedding:                                                              
In all cases, the minimum depth should be nominally 2mm to ensure sufficent adhesive is in place and afford reasonable compressive strength. There is no maximum thickness reqirement. No primer is required to facilitate adhesion unless the surface is loose or friable. In cool environments, pre warm the product before use.      
                                                                 
Adhesive Applications:                                                            
Apply a thin coat of Epigen 911 to both surfaces before bringing the two together. Do not use where a flexible or resilient glue line is required. Recommended where strength or heavy shock resistant is required (eg: Ceramic Tiles to Steel on chutes, steel onto steel, concrete onto steel). Preheat the material before use to achieve best cure rate and strength.
                                                                 
Crack Repairs:                                                            
In horizontal installations, open up cracks using a grinder before applying directly into crack. In vertical installations, use an abrasive bit on a drill and follow the crack keeping the surface shoulders narrow.                            

COVERAGE GUIDE    
Bedding Application - nominally 5mm thickness 
         
7kg = 1000mm X 1000mm X 5mm  
         
Adhesive or Void Filling Application   
         
1.4kg = 1 litre      
         
1.4kg = 100mm X 100mm X 100mm  



CHEMICAL RESISTANCE
Tested at 21oC. Samples cured for 10 days at 25oC. Curing at elevated temperatures will improve chemical resistance.
 
1 = Continuous or long term immersion
2 = Short term immersion
3 = Splash and spills
4 = Avoid contact

 

 

Acetic Acid, 10 % 2 Acetone 2
Acetic Acid, Glacial 2 Ammonium Chloride 1
Hydrochloric Acid, 5 % 1 Beer 1
Hydrochloric Acid, 10 % 2 Dichloromethane 4
Hydrochloric Acid, conc 2 Diesel Fuel 1
Nitric Acid, 5 %  2 Isopropyl Alcohol 2
Nitric Acid, 10 % 2 Kerosene 1
Phosphoric Acid, 5 % 1 Petrol 2
Phosphoric Acid, 20 % 2 Salt Water 1
Sulfuric Acid, 5 % 3 Sewage 2
Sulfuric Acid, 20 % 3 Skydrol 2
Ammonium Hydroxide, 5 % 1 Sodium Cyanide 1
Ammonium Hydroxide, 20 % 1 Sodium Hypochlorite 2
Potassium Hydroxide, 5 % 1 Toluene 2
Potassium Hydroxide, 20 % 1 Trichloroethane 3
Sodium Hydroxide, 5 % 1 Wine 2
Sodium Hydroxide, 20 % 1 Xylene 2

CURE

Variations in cure may arise due to the amount of material being applied, the thickness of material being applied, the surface temperature, and the product temperature. The cure may be increased by heating product or by leaving mixed material stand for 15 minutes before use. The cure may be decreased by cooling the product before mixing.

FAST CURE ADHESIVE & PATCH epigen FC1

FAST CURE GROUT epigen FC4

BONDING & REPAIR ADHESIVE epigen 1009

EPOXY BACKING GROUT epigen 0301

HIGH STRENGTH EPOXY ADHESIVE epigen 0907

HEAT RESISTANT ADHESIVE epigen XD003

ELASTOMERIC BINDER & PRIMER Epigen 0411


Switch to Mobile Version